Jump to the main content

Search Home DIY Online

Screw Size Chart and Pilot Hole Sizes for Wood

Posted by Posted Topic: Hand Tools

A pilot hole is a narrow hole in the wood the screw threads bite into, and a clearance hole is a wider one the unthreaded shank slides through. For a #8 wood screw (0.164 in), Gardner Screw Corporation's chart gives a 0.116 in pilot hole in hard wood, 0.076 in in soft wood and an 11/64 in clearance hole.

Assorted wood screws on a workbench beside a drill

Covered in the guide: Hand Tools for Beginners: Where to Start

What size pilot hole does a screw need?

It depends on the screw gauge and the wood. For a #8 wood screw, Gardner Screw Corporation’s published chart gives a 0.116 in pilot in hard wood, a 0.076 in pilot in soft wood and an 11/64 in clearance hole. The screw size and pilot hole chart lists every gauge from #2 to #18 with millimetres.

Choosing the right hole is one of the basic skills in our beginner hand tools guide. This page explains how to read the numbers.

How do you read a screw gauge?

The number after the hash is the gauge, a code for the thread diameter. On Gardner’s chart a #6 is 0.138 in, a #8 is 0.164 in (4.17 mm) and a #10 is 0.190 in. Each step up adds about 0.013 in. Multiply inches by 25.4 for millimetres (NIST).

What is a pilot hole and what is a clearance hole?

A pilot hole is drilled into the piece the threads grip, and is smaller than the screw so the threads can cut in. A clearance hole goes through the first piece, is about as wide as the shank, and lets the screw pull the two pieces together. Gardner’s chart gives both.

Which pilot hole for softwood and hardwood?

Use the larger pilot in dense wood.

Gauge Screw diameter Clearance hole Pilot, hard wood Pilot, soft wood
#6 0.138 in 9/64 in (No. 27) 3/32 in (No. 42) 1/16 in (No. 52)
#8 0.164 in 11/64 in (No. 18) 7/64 in (No. 32) 5/64 in (No. 48)
#10 0.190 in 3/16 in (No. 10) 9/64 in (No. 28) 3/32 in (No. 43)

Gardner says these sizes are for average conditions and may need adjusting for the wood, so drill a test hole in scrap first.

What about metal and drywall?

This chart is for wood screws only. Sheet-metal, machine and drywall screws use different sizes. Check the maker’s instructions for the screw and the material before you drill.

Which drill bit sizes match the chart?

Gardner prints the nearest fraction and a number drill, which are wire-gauge sizes common in drill sets. A fractional bit close to the decimal size also works. Our guide to choosing drill bits explains sets and sizes.

Worked example: a #8 screw in oak

  1. Screw: #8 is 0.164 in
  2. Oak is hard wood, so the pilot is 0.116 in, nearest fraction 7/64 in
  3. The piece you pull tight gets an 11/64 in clearance hole
  4. Drill a test hole in scrap, drive the screw and check it pulls flush without splitting

What mistakes should you avoid?

  • Skipping the test piece. The chart is for average wood.
  • Using the clearance size for the pilot. The screw will not grip.
  • Driving too hard. Stripped heads and splits come from torque, which the torque settings guide explains.
  • Using the wrong driver. See screwdrivers 101 for the match, and the drill buying guide for the tool itself.

Questions we get

What drill bit do I use for a #8 screw?

For a #8 wood screw, Gardner Screw Corporation's chart gives a 0.116 in pilot hole (near 7/64 in, drill No. 32) in hard wood and a 0.076 in pilot hole (near 5/64 in, drill No. 48) in soft wood. The clearance hole for the shank is 11/64 in (drill No. 18). Test on a scrap of the same wood before you drill the workpiece.

What is the difference between a pilot hole and a clearance hole?

The pilot hole goes into the piece the screw threads grip, and is smaller than the screw's outer diameter so the threads can cut into the wood. The clearance hole goes through the piece you are pulling tight and is about as wide as the shank, so the screw slides through and draws the pieces together. Gardner's chart lists both.

Should the pilot hole be bigger for hardwood?

Yes. Dense wood resists the threads, so the chart calls for a larger pilot. For a #8 screw the hard wood pilot is 71 percent of the screw diameter and the soft wood pilot is 46 percent (0.116 and 0.076 in against 0.164 in). Test on scrap first.

What happens if the pilot hole is too small or too big?

Gardner's catalog says a hole that is too large leaves too little gripping surface, and an undersized pilot weakens the fastening because the wood fibers are crushed and packed into the thread root, which sets up stresses that tend to split or crack the wood. Match the hole to the wood and test on a scrap.

Do I need to pre-drill every screw?

No. Gardner says every recommendation is for average conditions, and some screws are designed to drive without pre-drilling. GRK says its RSS structural screw does not require predrilling, but suggests it in very hard, dense wood such as mahogany if the screw will not fully drive, or if torque is splitting the wood. Always check the instructions for the screw you are using.

Where we got this

  1. Gardner Screw Corporation, Hi-Torque Wood Screws: Recommended Drill and Bit Sizes (catalog, 01B-09/07) (s3.amazonaws.com)
  2. GRK Fasteners, GRK Installation Technical Bulletin (predrilling in hard wood) (grkfasteners.ca)
  3. NIST SP 811, Appendix B.8: inch = 25.4 mm (exact) (nist.gov)

Keep reading

Return to top